Hey everyone, I’m really frustrated here. My electric EZGO golf cart has decided to take a day off, it seems. I press the pedal, and it’s like it’s laughing at me—no movement at all! Anyone else had this issue? How did you resolve it?
Response
Hi there. I’ve been in the same boat with my EZGO. One thing that really made a difference for me was going through all the battery connections and tightening them up. Let’s dive deeper into the solutions that have worked for many.
Solutions that worked for users
| Solution | Users Who Found Success | Personal Experience | Estimated Cost (USD) | Time Needed (Minutes) |
|---|---|---|---|---|
| Check Battery Connections | 3 | Tightened loose connections and it worked | $0 | 5-10 |
| Check Solenoid | 2 | Replaced a faulty solenoid and the cart moved | $20-$50 | 15-30 |
| Inspect F/R Switch | 1 | Switched to “Forward” and the cart started moving | $0 | 5-10 |
Symptoms
- Golf cart doesn’t move when the pedal is pressed
- You hear the motor, but the cart stands still
- Cart moves but then stops suddenly
Possible Causes
- Loose or disconnected battery cables
- Faulty solenoid
- Damaged or misaligned F/R switch
- Software glitches in the controller
Solutions that Worked
1. Check Battery Connections
What I Did:
Checked and tightened all the battery connections, including the terminals and wires.
Outcome:
The cart started moving smoothly.
Personal Experience:
I found a couple of battery connections that were not just loose but also corroded. After cleaning and tightening them, the cart was good to go.
Estimated Cost:
$0
Time Needed:
5-10 minutes
Steps:
- Open the battery compartment using the latch or screws.
- Put on gloves for safety.
- Inspect all battery connections, including the terminals and wires.
- Use a wrench to tighten any loose connections.
- If you see corrosion, clean it off using a wire brush.
Expert Tip:
Always disconnect the battery before working on any electrical components. This will prevent accidental short circuits.
2. Check Solenoid
What I Did:
Tested and replaced the faulty solenoid.
Outcome:
The cart started moving again.
Personal Experience:
The solenoid was making a clicking noise but wasn’t engaging. A quick replacement did the trick.
Estimated Cost:
$20-$50
Time Needed:
15-30 minutes
Steps:
- Locate the solenoid, usually near the batteries.
- Disconnect the battery for safety.
- Use a multimeter to test the solenoid for continuity.
- If faulty, remove the old solenoid by disconnecting the wires.
- Install the new solenoid and reconnect the wires.
Expert Tip:
Always take a photo of the solenoid and its connections before removing it. This will help you install the new one correctly.
3. Inspect F/R Switch
What I Did:
Checked the F/R (Forward/Reverse) switch and set it to “Forward.”
Outcome:
The cart started moving.
Personal Experience:
The F/R switch was stuck in the neutral position. A little jiggle and it was back in business.
Estimated Cost:
$0
Time Needed:
5-10 minutes
Steps:
- Locate the F/R switch, usually near the driver’s seat.
- Make sure it’s not stuck or jammed.
- Set it to either “Forward” or “Reverse,” avoiding the “Neutral” position.
- Test the cart to see if it moves.
Expert Tip:
If the F/R switch feels loose or wobbly, it might be worn out and in need of replacement.
Safety tips
- Software Reset: Sometimes, a simple controller reset can solve the issue. Turn off the cart, wait for a few minutes, and then turn it back on.
- Check for Error Codes: Some modern EZGO carts have a diagnostic mode that can display error codes. Refer to your manual on how to access this mode.
- Emergency Brake: Ensure that the emergency brake is not engaged. It’s a simple oversight but happens more often than you’d think.
Golf Cart Models Where This Worked
- EZGO TXT
- EZGO RXV
Hope this comprehensive guide helps anyone facing similar issues with their electric EZGO golf carts! Feel free to share your experiences and solutions.