The PING G2 EZ driver has a fixed hosel with no wrench-adjustable loft or lie. The captured factory loft is 15.5°; the listed lie is Not reliably published. Useful tuning comes from tee height, ball position, strike location, playing length and shaft fit rather than a sleeve.
PING Fixed-Hosel Driver Tuning Guide
G2 EZ
Fixed hosel • 2004
FixedHosel
15.5° standard EZ configurationFactory lofts
Not reliably publishedListed lie
Game-improvementModel type
What is actually adjustable?
| Loft / lie by wrench | No — the stock hosel is fixed. |
|---|---|
| Factory shot-shape weight | No normal user-movable CG system. |
| Tee height / ball position | Yes — fastest reversible launch/strike tuning. |
| Playing length / shaft | Yes — by normal club-building work. |
| Lead tape | Yes — mainly for head feel and small CG/bias changes. |
Use impact location before changing settings
| Strike | Typical effect | What to try first |
|---|---|---|
| High face | Often raises launch and reduces spin | If flight is already high and low-spin, do not keep raising the tee. |
| Low face | Often lowers launch and adds spin | Raise tee height slightly before changing loft. |
| Heel | Can add fade/slice gear effect | Improve centred contact before stacking more draw bias. |
| Toe | Can add draw/hook gear effect | Check strike before adding more draw/upright bias. |
If the G2 EZ launches too low
- Raise tee height slightly if impact is low on the face; low-face contact can suppress launch and add spin.
- This model was captured only in 15.5°, so a true static-loft increase requires a different higher-loft driver/head rather than another version of this same head.
If it launches too high
- Lower the tee slightly and check whether contact is excessively high on the face.
- This model was captured only in 15.5°, so a true static-loft reduction requires a different lower-loft driver/head.
If you are fighting a slice
- After strike is reasonable, start with about 2 g of lead tape toward the heel if you want a small draw-bias nudge.
- If the miss comes with heel strikes, fix contact before chasing a new shaft.
If you are fighting a hook
- After checking toe strikes, about 2 g of lead tape toward the toe can provide a small fade-bias/head-feel nudge.
- A fixed hosel cannot simply be flattened or opened with a wrench.
Factory loft choices
| Loft | Best starting use |
|---|---|
| 15.5° | Only captured loft for this model; changing static loft means moving to a different driver/head. |
Lead-tape tuning: how much and where
| Heel | Start around 2 g for a modest draw-bias/head-feel change; test before adding more. |
|---|---|
| Toe | Start around 2 g for a modest fade-bias/head-feel change. |
| Rear | Adds head mass and may slightly favour stability; it will not turn an older head into a modern high-MOI design. |
| How much? | About 2 g at the head is roughly one swing-weight point on a typical driver, but exact change depends on length and build. |
30-second baseline setup
- Start with roughly half the ball above the crown.
- Play the ball around the lead heel as a baseline.
- Mark impact before changing hardware.
- Use small lead-tape changes only after strike is repeatable.
- If launch is fundamentally wrong, move to a different driver/head with the loft you actually need rather than trying to bend this hosel.
What not to do
- Do not attack the hosel with a modern PING wrench; there is no adjustable sleeve.
- Do not heat or bend the bonded hosel as a normal consumer adjustment.
- Do not assume a sole screw is a movable shot-shape weight unless PING documents it that way.
Disclaimer: Specifications and adjustment hardware can vary by model year, region and component configuration. Before altering the club, confirm the correct procedure with official PING documentation or a PING-authorized fitter for your exact driver.