The PING G2 driver has a fixed hosel with no wrench-adjustable loft or lie. Factory loft coverage runs 7° to 11.5°; the listed lie is 58°. Useful tuning comes from tee height, ball position, strike location, playing length and shaft fit rather than a sleeve.
PING Fixed-Hosel Driver Tuning Guide
G2
Fixed hosel • 2004
FixedHosel
7°, 8.5°, 10°, 11.5°Factory lofts
58°Listed lie
MenModel type
What is actually adjustable?
| Loft / lie by wrench | No — the stock hosel is fixed. |
|---|---|
| Factory shot-shape weight | No normal user-movable CG system. |
| Tee height / ball position | Yes — fastest reversible launch/strike tuning. |
| Playing length / shaft | Yes — by normal club-building work. |
| Lead tape | Yes — mainly for head feel and small CG/bias changes. |
Use impact location before changing settings
| Strike | Typical effect | What to try first |
|---|---|---|
| High face | Often raises launch and reduces spin | If flight is already high and low-spin, do not keep raising the tee. |
| Low face | Often lowers launch and adds spin | Raise tee height slightly before changing loft. |
| Heel | Can add fade/slice gear effect | Improve centred contact before stacking more draw bias. |
| Toe | Can add draw/hook gear effect | Check strike before adding more draw/upright bias. |
If the G2 launches too low
- Raise tee height slightly if impact is low on the face; low-face contact can suppress launch and add spin.
- If you need a permanent loft increase, the proper head-level solution is the 11.5° factory option rather than trying to bend the hosel.
If it launches too high
- Lower the tee slightly and check whether contact is excessively high on the face.
- If you genuinely need less static loft, the 7° factory option is the stronger head-level choice.
If you are fighting a slice
- After strike is reasonable, start with about 2 g of lead tape toward the heel if you want a small draw-bias nudge.
- If the miss comes with heel strikes, fix contact before chasing a new shaft.
If you are fighting a hook
- After checking toe strikes, about 2 g of lead tape toward the toe can provide a small fade-bias/head-feel nudge.
- A fixed hosel cannot simply be flattened or opened with a wrench.
Factory loft choices
| Loft | Best starting use |
|---|---|
| 7° | Lowest-loft factory option; strongest starting point for players already producing enough launch. |
| 8.5° | Middle-ground factory loft. |
| 10° | Middle-ground factory loft. |
| 11.5° | Highest-loft factory option; easiest starting point for more launch and carry. |
Lead-tape tuning: how much and where
| Heel | Start around 2 g for a modest draw-bias/head-feel change; test before adding more. |
|---|---|
| Toe | Start around 2 g for a modest fade-bias/head-feel change. |
| Rear | Adds head mass and may slightly favour stability; it will not turn an older head into a modern high-MOI design. |
| How much? | About 2 g at the head is roughly one swing-weight point on a typical driver, but exact change depends on length and build. |
30-second baseline setup
- Start with roughly half the ball above the crown.
- Play the ball around the lead heel as a baseline.
- Mark impact before changing hardware.
- Use small lead-tape changes only after strike is repeatable.
- If launch is fundamentally wrong, move to the appropriate factory loft rather than trying to bend the hosel.
What not to do
- Do not attack the hosel with a modern PING wrench; there is no adjustable sleeve.
- Do not heat or bend the bonded hosel as a normal consumer adjustment.
- Do not assume a sole screw is a movable shot-shape weight unless PING documents it that way.
Disclaimer: Specifications and adjustment hardware can vary by model year, region and component configuration. Before altering the club, confirm the correct procedure with official PING documentation or a PING-authorized fitter for your exact driver.