TaylorMade Qi Max Iron Lie Angle Chart

The TaylorMade Qi Max Irons lie-angle progression runs from 61.5°–64.5° using TaylorMade’s published specifications. The 7-iron at 28° is the strongest mid-set fitting reference, while the higher-loft short irons deserve the closest dynamic check.

TaylorMade Dynamic Lie Angle Guide

Iron

61.5°–64.5°Official lie reference
35–39.125 inPlaying length
Fitter adjustmentFitting route
Official TaylorMadeData status

Qi Max Irons lie-angle fingerprint

61.5°–64.5°Official lie reference
35–39.125 inPlaying length
Fitter adjustmentFitting route
Official TaylorMadeData status

What stands out about the Qi Max Irons lie setup?

The published lie values span across the lineup.

The progression becomes more upright through the set and then levels off in the scoring clubs where TaylorMade keeps multiple wedges at the same lie.

A professional loft-and-lie machine is the correct way to test a permanent lie change.

Factory lie angle chart

Club Loft Lie Length Step Pattern
4-iron 18.5° 61.5° 39.125 in Starting lie
5-iron 21° 62° 38.5 in +0.5° More upright
6-iron 24° 62.5° 37.88 in +0.5° More upright
7-iron 28° 63° 37.25 in +0.5° More upright
8-iron 32.5° 63.5° 36.75 in +0.5° More upright
9-iron 37° 64° 36.25 in +0.5° More upright
PW 42.5° 64.5° 35.75 in +0.5° More upright
AW 48° 64.5° 35.5 in Same lie
SW 54° 64.5° 35.25 in Same lie
LW 58° 64.5° 35 in Same lie

Lie progression visual

TaylorMade’s published lie progression for this exact model.
4-iron
61.5°
5-iron
62°
6-iron
62.5°
7-iron
63°
8-iron
63.5°
9-iron
64°
PW
64.5°
AW
64.5°
SW
64.5°
LW
64.5°

Qi Max Irons directional effect from a 1° lie error

Geometric face-plane direction estimate using the published lofts. It is not predicted curvature or yards offline.
4-iron
0.33°
5-iron
0.38°
6-iron
0.45°
7-iron
0.53°
8-iron
0.64°
9-iron
0.75°
PW
0.92°
AW
1.11°
SW
1.38°
LW
1.60°
Most lie-sensitive listed club: LW at 58° loft — roughly 1.60° of face-plane direction change from a 1° lie error.

Dynamic lie test for the TaylorMade Qi Max Irons

65°1° upright test

Only test if the head is safe to bend and dynamic evidence supports it.

64°Published baseline

Record centred strike and start direction before changing anything.

63°1° flat test

Keep setup and ball position consistent.

Should the TaylorMade Qi Max Irons be more upright or flatter?

Try more upright if…

  • Your solid strikes repeatedly start right of target even when face control is good.
  • The toe is noticeably lower than the heel through impact or your strike board / marker test points to a toe-down delivery.
  • You feel you have to raise your hands unnaturally just to get the sole to sit correctly.
  • A 1° upright test produces a straighter start line without moving impact away from the centre.

Try flatter if…

  • Your solid strikes repeatedly start left of target even when face control is good.
  • The heel is lower than the toe through impact or a dynamic lie test shows the club is arriving too upright.
  • The heel tends to grab the turf first on otherwise centred strikes.
  • A 1° flatter test straightens the start line while keeping contact centred.

Lie angle probably is not the main problem if…

  • Contact moves all over the face from swing to swing.
  • Your misses are mainly hooks or slices caused by face-to-path rather than start direction.
  • The club is the wrong playing length or your posture changes significantly from shot to shot.
  • One bad shot is the only evidence pointing toward a lie change.
Verify the exact TaylorMade specifications before relying on these numbers

Golf-club specifications can differ by model year, loft, region, custom build and adjustable-hosel setting. Before buying, fitting or changing a club, compare these figures with TaylorMade’s official specifications for your exact model. If a measurement is critical, have the club checked by a qualified fitter. Verify with TaylorMade.