TaylorMade P770 Irons (2024 generation) Iron Lie Angle Chart

The TaylorMade P770 Irons (2024 generation) lie-angle progression runs from 60.5°–64° using TaylorMade’s published specifications. The 7-iron at 33° is the strongest mid-set fitting reference, while the higher-loft short irons deserve the closest dynamic check.

TaylorMade Dynamic Lie Angle Guide

Iron

60.5°–64°Official lie reference
35.5–39 inPlaying length
Fitter adjustmentFitting route
Official TaylorMadeData status

P770 Irons (2024 generation) lie-angle fingerprint

60.5°–64°Official lie reference
35.5–39 inPlaying length
Fitter adjustmentFitting route
Official TaylorMadeData status

What stands out about the P770 Irons (2024 generation) lie setup?

The published lie values span 3.5° across the lineup.

The progression becomes more upright through the set and then levels off in the scoring clubs where TaylorMade keeps multiple wedges at the same lie.

A professional loft-and-lie machine is the correct way to test a permanent lie change.

Factory lie angle chart

Club Loft Lie Length Step Pattern
3-iron 19.5° 60.5° 39 in Starting lie
4-iron 22.5° 61° 38.5 in +0.5° More upright
5-iron 25.5° 61.5° 38 in +0.5° More upright
6-iron 29° 62° 37.5 in +0.5° More upright
7-iron 33° 62.5° 37 in +0.5° More upright
8-iron 37° 63° 36.5 in +0.5° More upright
9-iron 41° 63.5° 36 in +0.5° More upright
PW 46° 64° 35.75 in +0.5° More upright
AW 51° 64° 35.5 in Same lie

Lie progression visual

TaylorMade’s published lie progression for this exact model.
3-iron
60.5°
4-iron
61°
5-iron
61.5°
6-iron
62°
7-iron
62.5°
8-iron
63°
9-iron
63.5°
PW
64°
AW
64°

P770 Irons (2024 generation) directional effect from a 1° lie error

Geometric face-plane direction estimate using the published lofts. It is not predicted curvature or yards offline.
3-iron
0.35°
4-iron
0.41°
5-iron
0.48°
6-iron
0.55°
7-iron
0.65°
8-iron
0.75°
9-iron
0.87°
PW
1.04°
AW
1.23°
Most lie-sensitive listed club: AW at 51° loft — roughly 1.23° of face-plane direction change from a 1° lie error.

Dynamic lie test for the TaylorMade P770 Irons (2024 generation)

63.5°1° upright test

Only test if the head is safe to bend and dynamic evidence supports it.

62.5°Published baseline

Record centred strike and start direction before changing anything.

61.5°1° flat test

Keep setup and ball position consistent.

Should the TaylorMade P770 Irons (2024 generation) be more upright or flatter?

Try more upright if…

  • Your solid strikes repeatedly start right of target even when face control is good.
  • The toe is noticeably lower than the heel through impact or your strike board / marker test points to a toe-down delivery.
  • You feel you have to raise your hands unnaturally just to get the sole to sit correctly.
  • A 1° upright test produces a straighter start line without moving impact away from the centre.

Try flatter if…

  • Your solid strikes repeatedly start left of target even when face control is good.
  • The heel is lower than the toe through impact or a dynamic lie test shows the club is arriving too upright.
  • The heel tends to grab the turf first on otherwise centred strikes.
  • A 1° flatter test straightens the start line while keeping contact centred.

Lie angle probably is not the main problem if…

  • Contact moves all over the face from swing to swing.
  • Your misses are mainly hooks or slices caused by face-to-path rather than start direction.
  • The club is the wrong playing length or your posture changes significantly from shot to shot.
  • One bad shot is the only evidence pointing toward a lie change.
Verify the exact TaylorMade specifications before relying on these numbers

Golf-club specifications can differ by model year, loft, region, custom build and adjustable-hosel setting. Before buying, fitting or changing a club, compare these figures with TaylorMade’s official specifications for your exact model. If a measurement is critical, have the club checked by a qualified fitter. Verify with TaylorMade.