The PING G10 Draw driver is offered in 5 listed factory lofts from 7.5° to 13.5°, covering a 6° span. The 7.5° head is the lowest-loft starting point, while 13.5° adds 6° of static loft. This is a fixed-hosel model, so the loft chart below is about the factory heads rather than sleeve settings.
G10 Draw Driver Loft Chart
| Club | Loft | Gap |
|---|---|---|
| 7.5° head | 7.5° | — |
| 9° head | 9° | 1.5° |
| 10.5° head | 10.5° | 1.5° |
| 12° head | 12° | 1.5° |
| 13.5° head | 13.5° | 1.5° |
Range: 7.5°–13.5° (6° total span).
Gapping: Every adjacent factory loft is spaced by 1.5°.
G10 Draw Driver Relative Loft Map
These bars compare the listed factory lofts relative to each other inside this model. They are not measured launch-monitor outputs. The goal is to show the practical starting-point difference between the lower and higher heads.
G10 Draw Driver Launch, Spin & Trajectory Snapshot
These color bars show the relative tendencies within this model. Loft usually moves launch the most, trajectory close behind, and spin more conservatively because actual spin also depends heavily on head design, CG and strike.
Low
Lower
Penetrating
Low
Lower
Penetrating
Mid
Mid
Balanced
High
Higher
Higher
High
Higher
Higher
How to use it: use the lower-loft heads if you want a flatter, stronger starting point. Move higher if you need easier launch, with trajectory usually moving along with loft and spin shown a bit more conservatively.
Loft Spread
The listed factory choices cover 6°, from 7.5° to 13.5°.
Choice Spacing
Every adjacent factory loft is spaced by 1.5°.
7.5° vs 13.5°
The 13.5° head has 6° more static loft than the 7.5° head. That is the cleanest factory-head comparison before fitting the rest of the setup.
G10 Draw vs Other PING Driver Lofts
This comparison uses each model’s lowest listed factory loft, so the numbers are being compared on the same basis.
| Model | Reference | Loft | Difference |
|---|---|---|---|
| G10 Draw | 7.5° head | 7.5° | This model |
| G10 | 7.5° head | 7.5° | Same lowest loft |
| G5 | 7.5° head | 7.5° | Same lowest loft |
| G2 | 7° head | 7° | 0.5° lower |
| Si3 380 | 7° head | 7° | 0.5° lower |
How Each G10 Draw Driver Loft Changes the Starting Point
| Club | Loft | What it means |
|---|---|---|
| 7.5° head | 7.5° | This is the lowest-loft factory head and the lower-launch starting point within this model’s listed range. Actual ball flight still depends heavily on delivered loft and strike. |
| 9° head | 9° | This sits between the lowest and highest factory heads and provides a middle launch starting point. Actual ball flight still depends heavily on delivered loft and strike. |
| 10.5° head | 10.5° | This sits between the lowest and highest factory heads and provides a middle launch starting point. Actual ball flight still depends heavily on delivered loft and strike. |
| 12° head | 12° | This sits between the lowest and highest factory heads and provides a middle launch starting point. Actual ball flight still depends heavily on delivered loft and strike. |
| 13.5° head | 13.5° | This is the highest-loft factory head and the higher-launch starting point within this model’s listed range. Actual ball flight still depends heavily on delivered loft and strike. |
Static factory loft is the starting point, not the final ball flight. Delivered loft, strike location and shaft fit still matter. This fixed-hosel model keeps the focus on choosing the right head loft to begin with.
PING G10 Draw Loft FAQs
What lofts does the PING G10 Draw driver come in?
The listed factory lofts are 7.5°, 9°, 10.5°, 12° and 13.5°.
What is the loft range of the G10 Draw?
It runs from 7.5° to 13.5°, a 6° total span.
What is the typical factory loft step?
The median adjacent step is 1.5°.
Which G10 Draw factory loft should launch highest?
The 13.5° head has the most static loft and should generally start higher, all else equal.
Can you adjust the loft with a wrench?
No. This is a fixed-hosel driver, so changing static loft means changing to a different head loft.
Is the lowest-loft G10 Draw automatically the longest?
No. Too little loft can reduce carry if launch gets too low. The best loft is the one that produces the strongest launch, spin and strike combination for the player.
Spec & fitting disclaimer: Loft availability, lie angle and hosel hardware can vary by year, region, handedness or component setup. Verify the exact club with PING’s official documentation or a PING-authorized fitter before making an adjustment or ordering a replacement.