Hey everyone, I’ve been pulling my hair out trying to unlock Freedom Mode on my EZGO TXT. I’ve tried a few things, but nothing seems to work. Anyone else faced this issue and found a solution?
Response
Try unplugging the run/tow switch from the controller. If that doesn’t work you may need to replace the controller.
Solutions that worked for users
| Solution | Users Who Found Success | Personal Experience | Estimated Cost (USD) | Time Needed (Minutes) |
|---|---|---|---|---|
| Unplug the Run/Tow Switch from the Controller | 1 | Unplugged and reinstalled the jumper | $0 | 5-10 |
| Replace the Controller | 1 | Replaced the controller | $100-$300 | 30-60 |
| Use Handheld Programmer for Curtis Controllers | 1 | Adjusted speed settings | $200-$400 | 15-30 |
| Purchase a Passkey | 1 | Activated speed of 17.5 MPH | $50-$100 | 5-10 |
| Use Mode 4 and Set to Max Speed of 14.8 MPH | 1 | Set the speed to 14.8 MPH | $0 | 5-10 |
Symptoms
- Cart won’t go into Freedom Mode
- Cart speed is limited
- Cart gives error beeps
Possible Causes
- Controller issues
- Incorrect settings
- Software glitches
- Battery issues
Solutions that Worked
1. Unplug the Run/Tow Switch from the Controller
What I Did:
Unplugged the run/tow switch from the controller and then reinstalled the jumper.
Outcome:
The cart went into Freedom Mode.
Personal Experience:
I was skeptical at first, but after unplugging and reinstalling the jumper, my cart finally went into Freedom Mode.
Estimated Cost:
$0
Time Needed:
5-10 minutes
Steps:
- Turn off the cart completely.
- Locate the run/tow switch on the cart, usually found near the controller.
- Unplug the switch from the controller carefully.
- Wait for about 30 seconds to a minute.
- Reinstall the jumper back into the switch.
- Turn the cart back on.
Expert Tip:
Make sure to turn off the cart before unplugging the run/tow switch to avoid any electrical issues. This simple step can make a big difference.
2. Replace the Controller
What I Did:
Purchased a new controller and replaced the old one.
Outcome:
The cart went into Freedom Mode.
Personal Experience:
I had to shell out some cash, but replacing the controller did the trick.
Estimated Cost:
$100-$300
Time Needed:
30-60 minutes
Steps:
- Research and purchase a new controller that is compatible with your EZGO TXT model.
- Turn off the cart and disconnect the battery.
- Locate the old controller and remove the screws securing it.
- Carefully disconnect the wires from the old controller.
- Install the new controller and reconnect the wires.
- Secure the new controller with screws.
- Reconnect the battery and turn on the cart.
Expert Tip:
Label the wires before disconnecting them from the old controller. This will make it easier to install the new one.
3. Use Handheld Programmer for Curtis Controllers
What I Did:
Used a handheld programmer to adjust the speed settings on the Curtis controller.
Outcome:
The cart went into Freedom Mode.
Personal Experience:
After using the handheld programmer, I was able to adjust the speed settings and unlock Freedom Mode.
Estimated Cost:
$200-$400
Time Needed:
15-30 minutes
Steps:
- Purchase or rent a handheld programmer compatible with Curtis controllers.
- Connect the programmer to the controller.
- Follow the on-screen instructions to adjust the speed settings.
- Disconnect the programmer and test the cart.
Expert Tip:
Make sure the programmer is compatible with your cart’s controller model to avoid any issues.
4. Purchase a Passkey
What I Did:
Purchased a passkey and used it to activate Freedom Mode.
Outcome:
The cart went into Freedom Mode.
Personal Experience:
After using the passkey, my cart’s speed increased to 17.5 MPH, unlocking Freedom Mode.
Estimated Cost:
$50-$100
Time Needed:
5-10 minutes
Steps:
- Purchase a passkey compatible with your cart model.
- Insert the passkey into the designated slot on the cart.
- Follow the activation instructions.
- Test the cart to confirm Freedom Mode is activated.
Expert Tip:
Some passkeys come with limited activations. Make sure to read the terms before purchasing.
5. Use Mode 4 and Set to Max Speed of 14.8 MPH
What I Did:
Set the cart to Mode 4 and adjusted the speed to a maximum of 14.8 MPH.
Outcome:
The cart went into Freedom Mode.
Personal Experience:
After setting the cart to Mode 4 and adjusting the speed, I was able to unlock Freedom Mode.
Estimated Cost:
$0
Time Needed:
5-10 minutes
Steps:
- Locate the mode switch on the cart.
- Set the switch to Mode 4.
- Use the speed adjustment knob to set the speed to a maximum of 14.8 MPH.
- Test the cart to confirm Freedom Mode is activated.
Expert Tip:
Mode 4 is often hidden in the settings menu. You may need to consult the manual to find it.
Safety info
- Always turn off the cart and disconnect the battery before performing any electrical work.
- Keep a set of tools handy. You’ll likely need a screwdriver, wrench, and possibly wire strippers.
- If you’re not comfortable with electrical work, consider hiring a professional to avoid damaging your cart further.
Extra tips
- Some carts may require a software update to unlock Freedom Mode. Check the manufacturer’s website for updates.
- If your cart has been modified, standard solutions may not work. You may need to consult with the person or company that modified the cart.
- Some solutions may void your warranty. Always check your warranty terms before proceeding with any modifications.
Cart Models Where This Worked
- 2016 RXV
- 2016 T48
- 2015 RXV
- 2009 EZGO TXT