The Cobra ZL driver has 3 listed factory loft options. The listed lofts are 8.5°, 9.5° and 10.5°. The chart focuses on the stated head lofts themselves; actual launch and spin still depend on delivery, strike and the rest of the build.
ZL Loft Chart
| Option | Loft | Gap |
|---|---|---|
| Option 1 | 8.5° | — |
| Option 2 | 9.5° | 1° |
| Option 3 | 10.5° | 1° |
Range: 8.5°–10.5° (2° total span).
Gapping: The median gap between adjacent listed lofts is 1°.
ZL Relative Loft Map
These bars compare the listed lofts relative to each other inside this model. They are not measured performance outputs.
ZL Launch, Spin & Trajectory Snapshot
These bars show the relative tendencies of the listed lofts within this model. They are not launch-monitor measurements; they simply visualize the practical difference between stronger and weaker lofts.
Lower
Lower
Flatter
Mid
Mid
Balanced
Higher
Higher
Higher
How to use it: Use the lower lofts for a stronger, flatter starting point and the higher lofts for easier launch. Actual ball flight still depends heavily on delivered loft and strike.
Loft Spread
The listed lofts cover 2°, from 8.5° to 10.5°.
Choice Spacing
The adjacent listed loft gaps run from 1° to 1°, with a median of 1°.
8.5° vs 10.5°
Moving from 8.5° to 10.5° adds 2° of static loft. The higher-loft option generally starts from an easier-launching, higher-spin baseline.
ZL vs Other Cobra Driver Lofts
This comparison uses each model’s lowest listed loft so the numbers are on the same basis.
| Model | Lowest Loft | Difference |
|---|---|---|
| ZL | 8.5° | This model |
| 414 Comp Tour | 8.5° | Same lowest loft |
| HS9 X | 8.5° | Same lowest loft |
| L5V | 8.5° | Same lowest loft |
| S2 | 8.5° | Same lowest loft |
How Each ZL Loft Changes the Starting Point
| Option | Loft | What it means |
|---|---|---|
| Option 1 | 8.5° | This is the strongest listed loft and the lowest-launching starting point within the model. |
| Option 2 | 9.5° | This sits between the strongest and weakest listed lofts for a more middle-of-the-range starting point. |
| Option 3 | 10.5° | This is the weakest listed loft and the easiest-launching starting point within the model. |
Cobra ZL Loft FAQs
What lofts does the Cobra ZL come in?
The listed lofts are 8.5°, 9.5° and 10.5°.
What is the loft range of the ZL?
It runs from 8.5° to 10.5°, a 2° total span.
What is the typical loft gap?
The median adjacent loft gap is 1°.
Which ZL loft should launch highest?
The 10.5° option is the highest listed loft and should provide the highest-launching starting point, all else equal.
Can you adjust the loft?
Not as a true loft-sleeve adjustment. The ZL uses Cobra Adjustable Flight Technology (AFT), which primarily changes face angle rather than giving you numbered loft settings. Loosen the hosel screw with the Cobra wrench, rotate the shaft/sleeve to O (Open), N (Neutral) or C (Closed), re-seat it, then tighten until the wrench clicks. Open tends to reduce effective loft when the face is returned square; Closed tends to add effective loft. If you need a specific measured loft, start with the correct factory-loft head rather than treating AFT like MyFly.
Does more loft always mean a better result?
No. The best loft depends on the club type, player delivery, strike and the distance or trajectory window you are trying to hit.
Spec & fitting disclaimer: Loft availability and specifications can vary by year, region, handedness and configuration. Verify the exact club with Cobra’s official documentation or an authorized fitter before ordering or adjusting equipment.