The Cobra RADSpeed One Length iron set has published lofts running from 19° in the 4-iron to 54° in the sand wedge, with lie angles progressing from 62.5°. A conservative 1° professional loft or lie change is the sensible first move unless a wider safe range is confirmed for the exact head. Bending 1° strong removes about 1° of effective bounce, while 1° weak adds about 1°. For a right-handed player, 1° upright tends to move the start line left and 1° flat tends to move it right. Because this is a ONE Length model, lie and length changes should preserve the single-length fitting concept.
RADSpeed One Length
2021
Stock geometry
| Club | Loft | Lie |
|---|---|---|
| 4 | 19° | — |
| 5 | 21° | — |
| 6 | 24° | — |
| 7 | 27.5° | — |
| 8 | 32° | — |
| 9 | 37° | — |
| PW | 42.5° | — |
| GW | 48° | — |
| SW | 54° | — |
Loft gap map
Factory spacing between clubs
2°
3°
3.5°
4.5°
5°
5.5°
5.5°
6°
Average loft spacing: 4.4°. A smooth gap pattern matters more than simply making one club stronger or weaker.
What a 1° bend actually changes
Slightly lower launch
Gap tightens to stronger club
Slightly higher launch
Gap tightens to weaker club
Lie-angle direction effect
Bendability verdict
The exact one-piece forged construction is not confirmed here. Use a conservative 1° first move and verify the head before larger bends.
Construction: Exact construction not fully documented.
1° bend reference
These are the resulting geometry numbers. They do not imply that every head is safe to bend.
| Club | Stock loft | 1° strong | 1° weak | Stock lie | 1° flat | 1° upright |
|---|---|---|---|---|---|---|
| 4 | 19° | 18° | 20° | — | — | — |
| 5 | 21° | 20° | 22° | — | — | — |
| 6 | 24° | 23° | 25° | — | — | — |
| 7 | 27.5° | 26.5° | 28.5° | — | — | — |
| 8 | 32° | 31° | 33° | — | — | — |
| 9 | 37° | 36° | 38° | — | — | — |
| PW | 42.5° | 41.5° | 43.5° | — | — | — |
| GW | 48° | 47° | 49° | — | — | — |
| SW | 54° | 53° | 55° | — | — | — |
Factory loft gaps
2°
3°
3.5°
4.5°
5°
5.5°
5.5°
6°
Average spacing: 4.4°. Check both neighbouring gaps before bending one club.
What bending changes
| Adjustment | Typical effect | What to watch |
|---|---|---|
| 1° strong | Lower static loft and about 1° less effective bounce | Lower flight tendency, more digging potential and a smaller gap to the stronger club |
| 1° weak | Higher static loft and about 1° more effective bounce | Higher flight tendency, more sole bounce and a smaller gap to the weaker club |
| 1° upright | For a right-handed golfer the start line generally moves left | Use dynamic lie and start-line evidence rather than trying to cure swing path |
| 1° flat | For a right-handed golfer the start line generally moves right | Left-handed direction is reversed |
Best fitting order
- Measure actual loft and lie before touching the head.
- Confirm the real problem with carry gaps, start line and turf interaction.
- Make the smallest useful change first — usually 1°.
- Re-measure the club after bending.
- Retest the two neighbouring clubs so the fix does not create a new gap.
Disclaimer: Safe bend limits vary by exact construction and condition. Use a qualified fitter and verify the specific head before larger loft or lie changes.