The Callaway Epic iron set has factory lofts from 20° and lie angles from 61° to 64°. Loft and lie may be adjusted by a qualified club fitter, depending on the exact head construction and condition.
Epic
model specific bending analysis • 2017
What stands out about the Epic specs?
Gap pattern: There is not enough individual club loft data to calculate a reliable progression.
Lie progression: The captured lie data is not complete enough to calculate a reliable set progression.
The long end begins 4-9i 20°. The scoring end finishes 4-9i 20°. Those two ends do not have to use identical loft spacing because launch, speed and carry compression are different.
Factory loft and lie chart
| Club | Loft | Lie | Loft gap | Gap read |
|---|---|---|---|---|
| 4-9i | 20° | — | — | — |
Where would I check for bending first?
Measure actual carry distances before deciding whether any loft needs to move.
No single club can be identified from the captured specs as the obvious gapping candidate.
How much bending makes sense for this set?
| Change | How it fits this model |
|---|---|
| 0.5°–1° | Best range to investigate first when one club is creating a small directional or carry gap problem. It is enough to matter without automatically rewriting the set’s factory progression. |
| 1°–2° | A meaningful change. On the Epic, compare the new loft against both neighbouring clubs so you do not create a second gap while fixing the first. |
| More than 2° | Large enough that bounce, offset and gapping consequences become substantial. Confirm head construction and the exact target with Callaway/a qualified fitter before considering it. |
- 1° strong → about 19° loft and roughly 1° less bounce.
- 2° strong → about 18° loft and roughly 2° less bounce.
- 1° weak → about 21° loft and roughly 1° more bounce.
- 2° weak → about 22° loft and roughly 2° more bounce.
These numbers show the geometry only; they do not mean this exact head is safe to bend by that amount.
Should the Epic be bent stronger?
The captured specs do not include a clear 7 iron loft, so this page avoids labeling the set as strong- or traditional-lofted.
- Strengthening loft generally lowers static loft, removes roughly the same amount of bounce, and slightly increases offset.
- Measure actual carry distances before deciding whether any loft needs to move.
- Do not strengthen a club merely because another Callaway iron has a lower printed loft.
Should the Epic be bent weaker?
- Weakening adds loft and approximately the same amount of bounce while slightly reducing offset.
- If a club launches too flat or creates too much carry separation, weakening may help; but compare it with both neighbouring carry numbers first.
- If the set is already in the unclassified category, the flight goal matters more than matching a generic loft chart.
How the actual loft gaps affect bending
The loft progression is fairly consistent, so a whole set change may preserve spacing, but only if the same flight problem exists throughout the set.
How the actual lie progression affects bending
The captured lie data is not complete enough to calculate a reliable set progression. Use dynamic lie and start direction individual club rather than copying a single lie change through the entire set.
| right handed player starts shots left with centred strike | Investigate flatter lie on the problem club(s). |
|---|---|
| right handed player starts shots right with centred strike | Investigate more upright lie. |
| left handed player | Reverse the left/right directional interpretation. |
| Only one club misbehaves | Measure that club against the set before applying a whole set lie change. |
Can you bend just one Epic iron?
Yes; and the spec pattern tells you when that may be smarter. Measure actual carry distances before deciding whether any loft needs to move. If the rest of the set produces good start lines and carry gaps, changing one measured problem club is more targeted than shifting all 1 captured clubs.
Should you bend the whole set?
The loft progression is fairly consistent, so a whole set change may preserve spacing, but only if the same flight problem exists throughout the set. For lie angle, a whole set change is more defensible when the same centred-strike start-direction pattern appears from long irons through scoring irons. For loft, whole set changes are rarely necessary just to solve one bad carry gap.
Used Epic irons: measure before copying factory specs
The factory chart is a reference, not proof of what a used club measures today. If the widest or tightest gap in this set also looks wrong on the launch monitor, measure those two clubs first: one may simply have drifted from its intended loft or been bent previously.
What bending changes besides the printed number
| 1° stronger | About 1° less loft, roughly 1° less bounce, slightly more offset, generally lower launch direction. |
|---|---|
| 1° weaker | About 1° more loft, roughly 1° more bounce, slightly less offset, generally higher launch direction. |
| More upright lie | For a right-hander, generally adds leftward start line influence. |
| Flatter lie | For a right-hander, generally adds rightward start line influence. |
Best bending workflow for this specific set
- Measure all captured clubs rather than assuming they still match the factory table.
- Start with the unusual gap(s) identified above, then compare actual carry distance, peak height and landing angle.
- For directional problems, use centred-strike start direction and dynamic lie rather than loft.
- Make the smallest useful change to one problem club first.
- Re-measure it immediately and compare it with both neighbouring clubs.
- Only expand the adjustment to more clubs if the same pattern is genuinely present.
When not to bend the Epic
- The requested change is only intended to copy another model’s loft numbers.
- The club’s poor result is caused by strike, shaft length, swingweight or delivery instead of loft/lie.
- The change would make an already tight factory loft gap even tighter without a carry-distance reason.
- The hosel shows prior stress, finish damage or evidence of repeated bending.
- The exact head construction has not been confirmed safe for the requested amount.
Disclaimer: Iron bendability varies with head construction, hosel design, finish, age, previous bending and condition. Do not assume a universal safe adjustment such as ±2°. Have a qualified club fitter measure the actual club and confirm the permitted adjustment with Callaway for your exact model before bending.