Club Car Carryall 272 Carburetor Adjustment & Settings

Older carbureted Club Car Carryall 272 versions use Club Car gasoline hardware that can vary by engine and year. Check the serial prefix first, then match idle, jetting and float settings to the exact carburetor.

Club Car Carburetor Guide

Carryall 272 • Adjustment & settings

Older carbureted gasoline versions.Applies to

Kawasaki FE-series or earlier Club Car gasoline; exact engine varies by yearEngine

Use the exact service-manual settingIdle

Identify FE290/FE350/earlier engine before using pilot, jet or idle dataMixture

Carryall 272 carburetor setup at a glance

Model-specific setup

This model spans older Club Car gasoline hardware. Engine identification matters because FE290 and FE350 carburetor settings are not interchangeable.

Carburetor: Legacy Club Car carbureted system

Before adjusting

This page covers older carbureted gasoline versions. Confirm the engine and carburetor match this setup before using any setting below.

VehicleClub Car Carryall 272

EngineKawasaki FE-series or earlier Club Car gasoline; exact engine varies by year.

CarburetorLegacy Club Car carbureted system.

Idle speed

Use the exact service-manual setting

Pilot / mixture

Identify FE290/FE350/earlier engine before using pilot, jet or idle data

Float level

Use the exact carburetor float-height specification

Choke

Fully open after warm-up; verify cable free play

Governor / linkage

Keep the factory governor and linkage setting

Before adjusting

Clean air filter, fresh fuel, correct spark, no intake leaks and free throttle linkage

1. IdentifyConfirm engine + carburetor family

2. Clean and inspectJets, bowl, needle, choke, intake boot

3. Set baselineIdle / pilot / float only from the right manual

4. RecheckWarm idle, takeoff, load response and hot restart

How to adjust the Club Car Carryall 272 carburetor

Confirm this Club Car Carryall 272 matches the carbureted setup shown above. If the vehicle has EFI or no carburetor, do not use these adjustments.

Identify the engine and carburetor before turning any screw. Engine/application: Kawasaki FE-series or earlier Club Car gasoline; exact engine varies by year. Carburetor: Legacy Club Car carbureted system.

Before adjusting anything, check fresh fuel, tank venting, fuel-filter and pump delivery, the air filter, intake boot or manifold, spark plug and choke operation. A carburetor setting will not fix a fuel restriction, intake leak or weak ignition.

Warm the engine fully and set idle using this baseline: Use the exact service-manual setting. Make sure throttle-cable tension or governor linkage is not holding the throttle plate open.

For the pilot/mixture circuit: Identify FE290/FE350/earlier engine before using pilot, jet or idle data. Only change an adjustment that the exact carburetor is designed to have, and make small changes before rechecking warm idle and throttle response.

For float and fuel level: Use the exact carburetor float-height specification. Then verify choke release, hot restart and smooth transition from idle into governed speed without surging, hesitation or flooding.

Carryall 272 carburetor symptoms

Runs only with choke

Usually points to a lean condition: dirty pilot and main circuit, restricted fuel supply or intake leak.

Black smoke / rich

Check that the choke fully opens, then inspect float and needle, fuel level and air filter.

Hunts or surges

Check pilot circuit, intake leaks and governor and throttle linkage before changing the idle stop.

High idle

Make sure cable tension or governor linkage is not holding the throttle plate open.

Stalls when warm

Check pilot passage, idle baseline, valve or compression condition and heat-related fuel restriction.

Bog when throttle opens

Inspect transition/main circuit and fuel delivery; an idle adjustment will not fix a blocked main jet.

Carryall 272 carburetor specifications

Applies to: Older carbureted gasoline versions.

Engine: Kawasaki FE-series or earlier Club Car gasoline; exact engine varies by year.

Carburetor: Legacy Club Car carbureted system.

Idle: Use the exact service-manual setting.

Mixture: Identify FE290/FE350/earlier engine before using pilot, jet or idle data.

Float: Use the exact carburetor float-height specification.

Choke: Fully open after warm-up; verify cable free play.

Governor: Keep the factory governor and linkage setting.

Model-specific note

This model spans older Club Car gasoline hardware. Engine identification matters because FE290 and FE350 carburetor settings are not interchangeable.

Club Car Carryall 272 carburetor FAQ

What is the correct Club Car Carryall 272 carburetor idle setting?

Use the exact service-manual setting. Confirm the exact model year and engine before using a numeric setting.

What is the Club Car Carryall 272 mixture-screw setting?

Identify FE290/FE350/earlier engine before using pilot, jet or idle data.

What is the Club Car Carryall 272 carburetor float setting?

Use the exact carburetor float-height specification.

Why does my Club Car Carryall 272 only run with the choke on?

That usually means the engine is running lean because of a restricted pilot and main passage, weak fuel delivery or an intake leak. Clean and diagnose the carburetor before simply richening the mixture.

Can the governor make a Club Car Carryall 272 look like the carburetor is out of adjustment?

Yes. Incorrect cable or governor linkage can hold the throttle open, cause hunting or limit throttle travel. Confirm linkage movement before changing carburetor settings.

What should I check before rebuilding the Club Car Carryall 272 carburetor?

Check fuel quality, tank vent, filter and pump delivery, air filter, intake leaks, choke operation, spark plug, valve or compression condition where applicable and throttle and governor linkage.

Match the carburetor to the exact vehicle

Idle RPM, pilot screw baseline, float height, jetting and governor and linkage settings can change by engine, carburetor and model year. This page applies to older carbureted gasoline versions. Verify the engine and carburetor ID before changing settings, and use the factory service manual for any value not explicitly listed here. For manufacturer documentation, visit the official manufacturer website.